• Contact Us
English (US)
ES Spanish
GR Greek
PL Polish
DE German
US English (US)
PT Portuguese
NL Dutch
FR French
RU Russian
IT Italian
  • Home
  • MEET
  • Shared functions MEET panels

[Meet panel M+K] relays, egress, admin car Acess webserver

Written by Tecnico Internacional

Updated at November 18th, 2026

  • MEET
    Monitors Shared functions MEET monitors Panels Shared functions MEET panels Guard Unit Others
  • DUOX
    Monitors
+ More

2 RELAY MODULE: REF.1490 2 RELAY

  • OPEN DOOR DELAY 0#: can’t be set, sync open door delay of panel.
  • OPEN DOOR DELAY 1#: The time that the open-door command has be sent and          the relay is not activated. The relay will active after the DOOR DELAY TIME be set, Open door relay is useful when the door is not close the panel. (option 0-9 s)

4 RELAY MODULE: Only available in panel programmed as PANEL 1.                
4 relay module (Ref. 1491 4 relay) must be connected to the RS485 port of the panel No.1. See INSTALLATION section for further details.

  • 1#-4# RELAY TIME: Time that the corresponding additional door relay keeps active (1-9s optional).
  • 1#-4# OPEN DOOR DELAY: The time that the open-door command has be sent and the relay is not activated. The relay will active after the DOOR DELAY TIME be set. Open door relay is useful when the door is not close the panel. (option 0-9 s).

EGRESS BUTTON: The egress button will available if the EGRESS BUTTON is be checked. the relay of panel and Ref.1490 will be activated if the egress button is activated.

PANEL RELAY REPEATER: It activates or deactivates the Ref.1490 2 relay module performance.

OPEN DOOR EXTENSION: DISABLE ,4 RELAY MODULE,2 RELAY MODULE, PANEL RELAY options.

  • 4 RELAY MODULE (REF.1491): associate with Relay 1-4 or CCTV relay in the monitor or Relay 1-4 icon in the concierge.
  • 2 RELAY MODULE (REF.1490): associate with Relay 1 in the monitor or concierge.
  • PANEL RELAY: associate with Relay 1-4 in the monitor.

ADMIN CARD: Admin/master card ID registered to enrol additional prox cards. This option is useful when there is not MEET MAGEMENT SOFTWARE available.               
When there is no management software, enter 0000 if you do not know the ID of the admin card. The first MIFARE prox card detected by the reader will act as admin/master card. The card of the residents can be added afterwards.         
To program user cards, present the admin/master card previously created on the card reader. The panel will enter in cards program mode. All the cards presented from now on will automatically updated in the panel and may be used to open the door.           
If there are not more cards to program, after two minutes the panel will exit program mode.              
There is not possible to deregister cards programmed by this method. Use the FERMAX MEET MANAGEMENT SOFTWARE for full operational possibilities.

DISARM BY CARD: When an already programmed user card is presented to the reader, and it has been previously assigned to a monitor, the alarm system of the corresponding apartment will change to HOME mode.

CARD READ PROMPTS: To disable, no tips when the panel read cards.

GUEST CODE: Guest code function can be enabled or disabled. The panel needs to be connected with a module Ref. 1494 to a third-party Access Control System. See INSTALLATION section.

WIEGAND Protocol used for Wiegand transmission (BURST or 26 BITS). Enter available parameter depending on the third-party Access Control System

FACILITY: Enter available parameter depending on the third-party Access Control System.

QR CODE:Enable or disabled QR code function.

WIEGAND:Protocol used for Wiegand transmission (26 BITS or 34 BITS). Enter available parameter depending on the third party Access Control System.

SITE CODE:The panel will verify site code of QR if the SITE CODE enable. The SITE CODE of QR must be same as filled in.

ACCESS PIN: To enable or disable the activation of the relay for ACCES PIN code.       
UP to 8 different PIN codes per panel. PIN length between 4 to 6 digits.

DOOR OPEN ALARM: An alarm will trigger if the door keeps opened after the programmed DOOR ALARM time. Options: disable, 30s. 60s. 120s, 180s and 250s.

DOOR FORCED ALARM: An alarm will trigger if an abnormal way to open the door has been detected, for example because there has not been any previous “open the door” command.

NOTE: 
his OPEN DOOR DELAY time will not apply to the egress button, door lock release that will be always immediate.

web server access control

Download Article

Related Articles

  • [Meet panel M+K] DIAGRAM INSTALLATION OF THE LIFT CONTROL SYSTEM REF.9545
  • [Meet panel] Block Panel Entrance webserver
  • [Meet panel] Open door delay acces webserver
  • [Meet panel] Management webserver

For more information, visit www.fermax.com
Contact: tec@fermax.com www.fermax.com/contact

Fermax logo

FERMAX ELECTRONICA S.A.U

Avenida Tres Cruces, 133
46017 Valencia, Spain

Expand